SEARS - 9.9 H.P. (1986-1987) - Special Tools

	Ref ID	Description	Price
		Flywheel Wedge~To remove flywheel. (#T 2989) Comment: TUNE UP Qty Required For Repair: TUNE UP	NLA
		Knock-off Nut~To remove flywheel. (#T 2909) Comment: TUNE UP Qty Required For Repair: TUNE UP	NLA
		Feeler Gauge~To adlust breaker points. (#T 8930 1) Comment: MANUAL STARTER Qty Required For Repair: MANUAL STARTER	NLA
		Starter Rewind Key~To rewind starter spring. (#T 2985) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Torque Wrench (0 - 100 lbs/ft)~To proporly secure fasteners. (#T 2998) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Torque Wrench (0 - 600 lbs/in.)~To properly secure fasteners. (#T 2999) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Carbon Brush~To remove carbon from inside of power head (#T 2991) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Hose Clamp Pliers~To remove and install fuel hose clamps. (#T 8900) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Seal Installer~To instail crankshaft seals. (#T 11202) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Seal Installer~To install upper crankshaft bearing cage seai. (#T 3012) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Seal SIeeve~To install upper crankshaft bearing cage seai. (#T 2908) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Adapter and Hex Bit~To torque connecting rod screws. (#T 8929) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Snap Ring Pliers~To remove and install piston pin retaining rings. (#T 1749) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Ring Compressor~To install pistons. (#T 2997) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Ring Expander~To install piston rings. (#T 8926) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Torque Wrench~To torque lower cylinder head bolts Adapter. (#T 8993) Comment: POWER HEAD Qty Required For Repair: POWER HEAD	NLA
		Puller~To remove propeller shaft bearing cage. (#T 8948 1) Comment: LOWER UNIT Qty Required For Repair: LOWER UNIT	NLA
		Seal Installer~To install shift rod seal. (#T 8957) Comment: LOWER UNIT Qty Required For Repair: LOWER UNIT	NLA
		Seal Installer~To install driveshaft seal in gear housing upper,propeller shaft (#T 2907) Comment: LOWER UNIT Qty Required For Repair: LOWER UNIT	NLA
		Battery Powered Test Light~To test for continuity in wires. (#T 2938 1) Comment: TEST EQUIPMENT Qty Required For Repair: TEST EQUIPMENT	NLA
		Test Prop~To test motor in test tank. (#T 8952) Comment: TEST EQUIPMENT Qty Required For Repair: TEST EQUIPMENT	NLA
		Leakage Tester~To test gear housing seals for leaks. (#T 8950) Comment: TEST EQUIPMENT Qty Required For Repair: TEST EQUIPMENT	NLA
		Clrcuit Tracer~To test 12 volt circuits for continuity. (#T 2951) Comment: TEST EQUIPMENT Qty Required For Repair: TEST EQUIPMENT	NLA
		Lubricant - Rykon Grease #2EP (#T 2961) Comment: LUBRICANTS AND SEALANTS Qty Required For Repair: LUBRICANTS AND SEALANTS	NLA
		Lubricant - Anti-seize (#T 2987 1) Comment: LUBRICANTS AND SEALANTS Qty Required For Repair: LUBRICANTS AND SEALANTS	NLA
		Lubricant - 7 OL #1 LPS-1 (#T 8969) Comment: LUBRICANTS AND SEALANTS Qty Required For Repair: LUBRICANTS AND SEALANTS	NLA
		Sealant - RTV (#T 8983) Comment: LUBRICANTS AND SEALANTS Qty Required For Repair: LUBRICANTS AND SEALANTS	NLA
		Sealant - 2 cc Loctite Retaining Compound #75 (#T 8936 1) Comment: LUBRICANTS AND SEALANTS Qty Required For Repair: LUBRICANTS AND SEALANTS	NLA
		Sealant - 50 cc Loctite H, Non-hardening Grade (#T 2962 2) Comment: LUBRICANTS AND SEALANTS Qty Required For Repair: LUBRICANTS AND SEALANTS	NLA
		Sealant - 2 OL Loctite D, Hardening Grade (#T 2963 2) Comment: LUBRICANTS AND SEALANTS Qty Required For Repair: LUBRICANTS AND SEALANTS	NLA
		Sealant Primer - 6 OL (#T 8935) Qty Required For Repair:	NLA

This assembly is found in these models:

SEARS > 9.9 H.P. (1986-1987)